TH-BLE: Difference between revisions
→Sensor sealing
| Line 136: | Line 136: | ||
== <big>'''Sensor sealing'''</big> == | == <big>'''Sensor sealing'''</big> == | ||
=== <big>'''Sealing | === <big>'''Sealing TH-BLE of the former design'''</big> === | ||
To seal the sensor and prevent unauthorized access to it, install the protective cover and pass the seal through the special holes in the cover. Tighten the seal against its end into the special hole in the seal. Cut off the excess wire of the seal. | To seal the sensor and prevent unauthorized access to it, install the protective cover and pass the seal through the special holes in the cover. Tighten the seal against its end into the special hole in the seal. Cut off the excess wire of the seal. | ||
[[File:Sealing former design DU-BLE.png]] | [[File:Sealing former design DU-BLE.png]] | ||
=== <big>'''Sealing | === <big>'''Sealing TH-BLE of the current design'''</big> === | ||
You will need the sensor protective cover and the seal provided in the kit<gallery widths="300" heights="300"> | You will need the sensor protective cover and the seal provided in the kit<gallery widths="300" heights="300"> | ||
File:New_design_cap.png|'''<big>Protective cover | File:New_design_cap.png|'''<big>Protective cover TH-BLE</big>''' | ||
File:New_design_seal.png|'''<big> | File:New_design_seal.png|'''<big>TH-BLE seal</big>''' | ||
</gallery>The cover is attached to the sensor head | </gallery>The cover is attached to the sensor head | ||
[[File:TD-BLE_with_cap.png|none|thumb|455x455px|'''<big> | [[File:TD-BLE_with_cap.png|none|thumb|455x455px|'''<big>TH-BLE with cap</big>''']] | ||
Then the seal itself is fixed in a special hole (it must be inserted to the end, with the '''closed end facing outward''')<gallery widths="350" heights="350"> | Then the seal itself is fixed in a special hole (it must be inserted to the end, with the '''closed end facing outward''')<gallery widths="350" heights="350"> | ||
File:Installing_TD-BLE_seal.png|'''<big>Installing | File:Installing_TD-BLE_seal.png|'''<big>Installing TH-BLE seal</big>''' | ||
File:Installed_TD-BLE_seal.png|'''<big>Installed | File:Installed_TD-BLE_seal.png|'''<big>Installed TH-BLE seal</big>''' | ||
</gallery>To remove the seal, screw in the special key from the kit (you can also use any self-tapping screw of suitable size) and pull it towards yourself. | </gallery>To remove the seal, screw in the special key from the kit (you can also use any self-tapping screw of suitable size) and pull it towards yourself. | ||
[[File:Removing_seal.png|none|thumb|493x493px|'''<big>Removing seal</big>''']] | [[File:Removing_seal.png|none|thumb|493x493px|'''<big>Removing seal</big>''']] | ||
| Line 157: | Line 157: | ||
This makes it impossible to remove the seal without damaging it. This provides additional protection against unauthorized access. | This makes it impossible to remove the seal without damaging it. This provides additional protection against unauthorized access. | ||
=== '''<big>Alternative sealing for | === '''<big>Alternative sealing for TH-BLE of the current design</big>''' === | ||
Also included with the current | Also included with the current TH-BLE is an alternative seal if a numbered seal is required. | ||
* The wire must be threaded through the hole in the sensor cover | * The wire must be threaded through the hole in the sensor cover | ||