TD-500: Difference between revisions
→Sealing sensor of the current design
| Line 731: | Line 731: | ||
You will need a sensor protective cover and a seal from the kit.<gallery widths="300" heights="300"> | You will need a sensor protective cover and a seal from the kit.<gallery widths="300" heights="300"> | ||
File:Protective cover for wired FLS.png|'''<big>Protective cover for wired FLS</big>''' | |||
File:New design seal.png|'''<big>Seal TD-500</big>''' | |||
</gallery>The cover is attached to the sensor head | </gallery>The cover is attached to the sensor head | ||
[[File:Wired FLS with protective cover.png|none|thumb|460x460px|'''<big>Wired FLS with protective cover</big>''']] | |||
[[ | |||
Then the seal itself is fixed in a special hole (it must be inserted to the end, with the '''closed end facing outwards''') | Then the seal itself is fixed in a special hole (it must be inserted to the end, with the '''closed end facing outwards''') | ||
| Line 742: | Line 741: | ||
Файл:Установленная пломба на проводной дут.png|'''<big>Установленная пломба на проводной дут</big>''' | Файл:Установленная пломба на проводной дут.png|'''<big>Установленная пломба на проводной дут</big>''' | ||
</gallery>To remove the seal, screw the special key from the kit into it (you can also use any self-tapping screw of a suitable size) and pull it towards you. | </gallery>To remove the seal, screw the special key from the kit into it (you can also use any self-tapping screw of a suitable size) and pull it towards you. | ||
[[File:Removal of the seal of the wired FLS.png|none|thumb|533x533px|'''<big>Removal of the seal of the wired FLS</big>''']] | |||
[[ | [[File:Seal after removal.png|none|thumb|'''<big>Seal after removal</big>''']] | ||
[[ | |||
Thus, it will be impossible to remove the seal without damaging it. This provides additional protection against unauthorized access. | Thus, it will be impossible to remove the seal without damaging it. This provides additional protection against unauthorized access. | ||
| Line 750: | Line 748: | ||
Also included with the sensor of the current sample is an alternative seal if a numbered seal is required. | Also included with the sensor of the current sample is an alternative seal if a numbered seal is required. | ||
* It is necessary to pass the cable through the hole in the sensor cover [[ | * It is necessary to pass the cable through the hole in the sensor cover | ||
* [[File:Alternative sealing of wired FLS step 1.png|frameless|511x511px]] | |||
* Pass both ends of the cable through the hole in the sensor head [[ | * Pass both ends of the cable through the hole in the sensor head | ||
* [[File:Alternative sealing of wired FLS step 2.png|frameless|517x517px]] | |||
* Pass both ends through the seal, tighten the cable and install the seal by pressing on the protruding part [[ | * Pass both ends through the seal, tighten the cable and install the seal by pressing on the protruding part | ||
* [[File:Alternative sealing of wired FLS step 3.png|frameless|664x664px]] | |||
== '''<big>Sealing sensor of the former design</big>''' == | == '''<big>Sealing sensor of the former design</big>''' == | ||
[[ | [[File:Sealing sensor of the former design.png|frameless|512x512px]] | ||
== '''<big>Cable sealing</big>''' == | == '''<big>Cable sealing</big>''' == | ||
To seal the sensor connector, insert a plastic seal into the special hole on the sensor connector | To seal the sensor connector, insert a plastic seal into the special hole on the sensor connector | ||
[[ | [[File:Wire sealing.png|frameless|493x493px]] | ||
= '''<big>Updating the sensor firmware</big>''' = | = '''<big>Updating the sensor firmware</big>''' = | ||