TD-600: Difference between revisions
→Setting the mode, range and network address
| Line 548: | Line 548: | ||
Go to Settings | Go to Settings | ||
[[ | [[File:Wired mobile settings button.png|frameless]] | ||
Select the mode you need('''1''') and press '''“Set parameters”'''('''2''') | Select the mode you need('''1''') and press '''“Set parameters”'''('''2''') | ||
| Line 554: | Line 554: | ||
[[Файл:Выбор режима ТД-600 мобильное приложение.png|941x941пкс]] | [[Файл:Выбор режима ТД-600 мобильное приложение.png|941x941пкс]] | ||
[[ | [[File:Wired set parameters mobile.png|frameless]] | ||
- '''Режим RS-485''' ('''RS485 mode''') следует выбрать, когда планируется подключать к линии А и В интерфейса RS-485 терминала. Терминал должен иметь функцию опроса датчиков, например запрашивать у них информацию. Терминал должен уметь опрашивать датчики в соответствии с '''протоколом LLS'''. На датчиках с серийным номером выше '''26339 RS-485 и''' '''RS-232 работают паралельно.''' | - '''Режим RS-485''' ('''RS485 mode''') следует выбрать, когда планируется подключать к линии А и В интерфейса RS-485 терминала. Терминал должен иметь функцию опроса датчиков, например запрашивать у них информацию. Терминал должен уметь опрашивать датчики в соответствии с '''протоколом LLS'''. На датчиках с серийным номером выше '''26339 RS-485 и''' '''RS-232 работают паралельно.''' | ||
| Line 581: | Line 581: | ||
After changing the range, press '''“Set parameters”''' ('''2'''). | After changing the range, press '''“Set parameters”''' ('''2'''). | ||
[[ | [[File:Wired setting range mobile.png|frameless|413x413px]] | ||
[[ | [[File:Wired set parameters mobile.png|frameless|845x845px]] | ||
'''The range 1-1023''' is most often used for sensors that are '''shorter than 1 meter'''. However, if we are talking about a stationary tank, the height of which is small, then the length and width are more than 2-3 m, it is better to choose the range 1-4095. | '''The range 1-1023''' is most often used for sensors that are '''shorter than 1 meter'''. However, if we are talking about a stationary tank, the height of which is small, then the length and width are more than 2-3 m, it is better to choose the range 1-4095. | ||
| Line 591: | Line 591: | ||
The default network address of the sensor is 1; if more than one unit is installed or other LLS devices are added, the network address on the sensor may need to be changed. The network address of each sensor must also be specified in the settings of the receiving device (navigation terminal).<blockquote>'''<big>Attention!!! There cannot be two devices with the same network address on the same line; this will cause a conflict.</big>'''</blockquote>To change the network address, enter a new address in the range '''0-255''' in the '''“Network address”''' field ('''1''') and click “'''Set parameters'''” ('''2''') | The default network address of the sensor is 1; if more than one unit is installed or other LLS devices are added, the network address on the sensor may need to be changed. The network address of each sensor must also be specified in the settings of the receiving device (navigation terminal).<blockquote>'''<big>Attention!!! There cannot be two devices with the same network address on the same line; this will cause a conflict.</big>'''</blockquote>To change the network address, enter a new address in the range '''0-255''' in the '''“Network address”''' field ('''1''') and click “'''Set parameters'''” ('''2''') | ||
[[ | [[File:Wired setting address.png|frameless|488x488px]] | ||
[[ | [[File:Wired set parameters mobile.png|frameless|845x845px]] | ||
== '''<big>Tank calibration</big>''' == | == '''<big>Tank calibration</big>''' == | ||