TD-BLE: Difference between revisions
→Installation locations in tanks of complex shapes
| Line 207: | Line 207: | ||
In this case, it is desirable to install two fuel level sensors in the deepest places along the geometric center of the depressions. | In this case, it is desirable to install two fuel level sensors in the deepest places along the geometric center of the depressions. | ||
[[ | [[File:Saddle shape.png|frameless|749x749px]] | ||
[[File:Saddle shape top view.png|frameless|749x749px]] | |||
[[File:Saddle shape side view.png|frameless|749x749px]] | |||
=== '''<big>Cylindrical tank</big>''' === | === '''<big>Cylindrical tank</big>''' === | ||
In this case, the sensor must be installed in the geometric center of the tank. | In this case, the sensor must be installed in the geometric center of the tank. | ||
[[ | [[File:Cylindrical tank.png|frameless|750x750px]] | ||
[[File:Cylindrical tank top view.png|frameless|750x750px]] | |||
[[File:Cylindrical tank inside view.png|frameless|750x750px]] | |||
==== '''<big>Long cylindrical tank</big>''' ==== | ==== '''<big>Long cylindrical tank</big>''' ==== | ||
In the case of elongated cylindrical tanks, to improve readings while driving, it is necessary to install two sensors at an equal distance from the geometric center of the tank. | In the case of elongated cylindrical tanks, to improve readings while driving, it is necessary to install two sensors at an equal distance from the geometric center of the tank. | ||
[[ | [[File:Cylindrical tank long.png|frameless|750x750px]] | ||
[[File:Cylindrical tank long inside view.png|frameless|750x750px]] | |||
==== '''<big>Ladder shape tank</big>''' ==== | ==== '''<big>Ladder shape tank</big>''' ==== | ||
If there is a difference in height in the tank and there is no common bed, it may be necessary to install two fuel level sensors. | If there is a difference in height in the tank and there is no common bed, it may be necessary to install two fuel level sensors. | ||
[[ | [[File:Ladder 2 tank.png|frameless|782x782px]] | ||
[[File:Ladder 2 tank inside view.png|frameless|750x750px]] | |||
===== '''<big>Ladder shape tank's tank calibration</big>''' ===== | ===== '''<big>Ladder shape tank's tank calibration</big>''' ===== | ||
| Line 237: | Line 249: | ||
На платформе "'''ДУТ 1'''" и "'''ДУТ 2'''" заводятся как отдельные датчики со своими таблицами и после создается третий вирутальный дачтик с суммой литров по двум датчикам, пример заведения двух дут на платформе показан [https://docs.google.com/document/d/1nZHXENAhi-Do6VU2j5PE9KCO3n76H2fw-wBG70zncXg/edit?usp=sharing в данной инструкции.] | На платформе "'''ДУТ 1'''" и "'''ДУТ 2'''" заводятся как отдельные датчики со своими таблицами и после создается третий вирутальный дачтик с суммой литров по двум датчикам, пример заведения двух дут на платформе показан [https://docs.google.com/document/d/1nZHXENAhi-Do6VU2j5PE9KCO3n76H2fw-wBG70zncXg/edit?usp=sharing в данной инструкции.] | ||
[[ | [[File:Ladder 2 tank calibration.png|frameless|750x750px]] | ||
== '''<big>Preparing the sensor</big>''' == | == '''<big>Preparing the sensor</big>''' == | ||