TD-150-BLE: Difference between revisions
→Setting the mode, range and network address
| Line 228: | Line 228: | ||
In the main menu, you can change the operating mode of the sensor. The name of the mode coincides with the interface that is used to physically connect the sensor to the GPS terminal | In the main menu, you can change the operating mode of the sensor. The name of the mode coincides with the interface that is used to physically connect the sensor to the GPS terminal | ||
Go to settings page | |||
[[ | [[File:TD-150 BLE settings page.png|frameless]] | ||
Select the mode you need ('''1''') and press '''“Set parameters”'''('''2''') | Select the mode you need ('''1''') and press '''“Set parameters”'''('''2''') | ||
[[ | [[File:TD-150 BLE mode setting.png|frameless]] | ||
[[ | [[File:TD-150 BLE set parameters.png|frameless]] | ||
- '''Passive RS485''' should be selected when you plan to connect to line A and B of the terminal's RS-485 interface. The terminal must have the function of polling sensors, for example, requesting information from them. The terminal must be able to interrogate sensors in accordance with the '''LLS protocol'''. | - '''Passive RS485''' should be selected when you plan to connect to line A and B of the terminal's RS-485 interface. The terminal must have the function of polling sensors, for example, requesting information from them. The terminal must be able to interrogate sensors in accordance with the '''LLS protocol'''. | ||
| Line 249: | Line 249: | ||
After changing the range, press '''“Set parameters”''' ('''2'''). | After changing the range, press '''“Set parameters”''' ('''2'''). | ||
[[ | [[File:TD-150 BLE range setting.png|frameless]] | ||
[[ | [[File:TD-150 BLE set parameters.png|frameless]] | ||
'''The range 1-1023''' is most often used for sensors that are '''shorter than 1 meter'''. However, if we are talking about a stationary tank, the height of which is small, but the length and width are more than 2-3 m, it is better to choose the range 1-4095. | '''The range 1-1023''' is most often used for sensors that are '''shorter than 1 meter'''. However, if we are talking about a stationary tank, the height of which is small, but the length and width are more than 2-3 m, it is better to choose the range 1-4095. | ||
| Line 259: | Line 259: | ||
The default network address of the sensor is 1; if more than one unit is installed or other LLS devices are added, the network address on the sensor may need to be changed. The network address of each sensor must also be specified in the settings of the receiving device (navigation terminal).<blockquote>'''<big>Attention!!! There cannot be two devices with the same network address on the same line; this will cause a conflict.</big>'''</blockquote>To change the network address, enter a new address in the range '''0-255''' in the '''“Network address”''' field ('''1''') and click “'''Set parameters'''” ('''2''') | The default network address of the sensor is 1; if more than one unit is installed or other LLS devices are added, the network address on the sensor may need to be changed. The network address of each sensor must also be specified in the settings of the receiving device (navigation terminal).<blockquote>'''<big>Attention!!! There cannot be two devices with the same network address on the same line; this will cause a conflict.</big>'''</blockquote>To change the network address, enter a new address in the range '''0-255''' in the '''“Network address”''' field ('''1''') and click “'''Set parameters'''” ('''2''') | ||
[[ | [[File:TD-150 BLE network address mobile.png|frameless]] | ||
[[ | [[File:TD-150 BLE set parameters.png|frameless]] | ||
== '''<big>Tank calibration</big>''' == | == '''<big>Tank calibration</big>''' == | ||