TD-500: Difference between revisions
→Remote control of FLS Escort
| Line 813: | Line 813: | ||
For RS-485, lines A and B of the converter must be connected to lines A and B of the sensor | For RS-485, lines A and B of the converter must be connected to lines A and B of the sensor | ||
[[File:RS-485 Logging Connections .png|none|thumb|579x579px|'''<big>RS-485 Logging Connections</big>''']] | [[File:RS-485 Logging Connections .png|none|thumb|579x579px|'''<big>RS-485 Logging Connections</big>''']] | ||
Run [https://drive.google.com/file/d/10i7v4TZ9-JDJYPAh-9JSh4x6vkM93BVV/view?usp=sharing terminal.exe] and configure the COM port as shown below: | |||
Baud rate – 19200, Parity – None, Stop-bits – 1, Handshaking – None | Baud rate – 19200, Parity – None, Stop-bits – 1, Handshaking – None | ||
| Line 842: | Line 842: | ||
= '''<big>Description of the LLS protocol</big>''' = | = '''<big>Description of the LLS protocol</big>''' = | ||
The protocol is described in this [https://docs.google.com/spreadsheets/d/12cmqjmKU7KKg6ms8wnTsv6Ttb1gohf8b/edit?usp=sharing&ouid=113197106569288024895&rtpof=true&sd=true document] | |||
Example of a request and response for 1 network address: | Example of a request and response for 1 network address: | ||
| Line 856: | Line 856: | ||
At the moment, Navtelecom and GlonassSoft terminals have the ability to configure wired Escort FLS by remotely connecting to the nav terminal without using the above commands. This can be done according to these instructions: | At the moment, Navtelecom and GlonassSoft terminals have the ability to configure wired Escort FLS by remotely connecting to the nav terminal without using the above commands. This can be done according to these instructions: | ||
'''[https://youtu.be/n_HxgImFvPs | '''[https://youtu.be/n_HxgImFvPs Smart and Signal, built-in configurator]''' | ||
'''[https://youtu.be/npxXyVOtfh0 | '''[https://youtu.be/npxXyVOtfh0 Smart and Signal by creating commands in the configurator]''' | ||
'''[https://www.youtube.com/watch?v=p6JkD-AuSHk | '''[https://www.youtube.com/watch?v=p6JkD-AuSHk UMKa]''' | ||
It is also possible to send commands via SMS commands or tracker terminal. | |||
At the moment, we know that the remote control function is supported by trackers of the Smart and Signal family produced by Navtelecom (Signal, Smart), Technocom (AvtoGRAPH) and GlonassSoft (UMKa). Transmission of commands to the sensor is possible only in RS-485 operating mode. | At the moment, we know that the remote control function is supported by trackers of the Smart and Signal family produced by Navtelecom (Signal, Smart), Technocom (AvtoGRAPH) and GlonassSoft (UMKa). Transmission of commands to the sensor is possible only in RS-485 operating mode. | ||
Для начала Вам необходимо открыть [https://www.fmeter.ru/download/_ftp/all/dut/FLS_Configurator.zip?v=210521143455 | Для начала Вам необходимо открыть [https://www.fmeter.ru/download/_ftp/all/dut/FLS_Configurator.zip?v=210521143455 PC configurator Escort]; преобразователь и\или трекер, при этом, должны быть отсоединены от компьютера. Во вкладке '''''Сервис''''' кликните на опцию '''''Дистанционное управление'''''. | ||
[[File:Remote control Settings.png|frameless|714x714px]] | [[File:Remote control Settings.png|frameless|714x714px]] | ||