TD-500: Difference between revisions
→Setting the mode, range and network address
| Line 518: | Line 518: | ||
Go to Settings | Go to Settings | ||
[[ | [[File:Wired mobile settings button.png|frameless]] | ||
Select the mode you need('''1''') and press '''“Set parameters”'''('''2''') | Select the mode you need('''1''') and press '''“Set parameters”'''('''2''') | ||
| Line 524: | Line 524: | ||
[[Файл:Выбор режима ТД-500 мобильное приложение.png|678x678пкс]] | [[Файл:Выбор режима ТД-500 мобильное приложение.png|678x678пкс]] | ||
[[ | [[File:TD-150 BLE set parameters.png|frameless]] | ||
* '''Пассивный RS485''' следует выбрать, когда планируется подключать к линии А и В интерфейса RS-485 терминала. Терминал должен иметь функцию опроса датчиков, например запрашивать у них информацию. Терминал должен уметь опрашивать датчики в соответствии с '''протоколом LLS''' или '''протоколом''' '''MODBUS ([[MODBUS ТД-500|описание]])''' | * '''Пассивный RS485''' следует выбрать, когда планируется подключать к линии А и В интерфейса RS-485 терминала. Терминал должен иметь функцию опроса датчиков, например запрашивать у них информацию. Терминал должен уметь опрашивать датчики в соответствии с '''протоколом LLS''' или '''протоколом''' '''MODBUS ([[MODBUS ТД-500|описание]])''' | ||
| Line 537: | Line 537: | ||
After changing the range, press '''“Set parameters”''' ('''2'''). | After changing the range, press '''“Set parameters”''' ('''2'''). | ||
[[ | [[File:Wired setting range mobile.png|frameless|450x450px]] | ||
[[ | [[File:TD-150 BLE set parameters.png|frameless|586x586px]] | ||
'''The range 1-1023''' is most often used for sensors that are '''shorter than 1 meter'''. However, if we are talking about a stationary tank, the height of which is small, then the length and width are more than 2-3 m, it is better to choose the range 1-4095. | '''The range 1-1023''' is most often used for sensors that are '''shorter than 1 meter'''. However, if we are talking about a stationary tank, the height of which is small, then the length and width are more than 2-3 m, it is better to choose the range 1-4095. | ||
| Line 547: | Line 547: | ||
The default network address of the sensor is 1; if more than one unit is installed or other LLS devices are added, the network address on the sensor may need to be changed. The network address of each sensor must also be specified in the settings of the receiving device (navigation terminal).<blockquote>'''<big>Attention!!! There cannot be two devices with the same network address on the same line; this will cause a conflict.</big>'''</blockquote>To change the network address, enter a new address in the range '''0-255''' in the '''“Network address”''' field ('''1''') and click “'''Set parameters'''” ('''2''') | The default network address of the sensor is 1; if more than one unit is installed or other LLS devices are added, the network address on the sensor may need to be changed. The network address of each sensor must also be specified in the settings of the receiving device (navigation terminal).<blockquote>'''<big>Attention!!! There cannot be two devices with the same network address on the same line; this will cause a conflict.</big>'''</blockquote>To change the network address, enter a new address in the range '''0-255''' in the '''“Network address”''' field ('''1''') and click “'''Set parameters'''” ('''2''') | ||
[[ | [[File:Wired setting address.png|frameless|514x514px]] | ||
[[ | [[File:TD-150 BLE set parameters.png|frameless|569x569px]] | ||
== '''<big>Tank calibration</big>''' == | == '''<big>Tank calibration</big>''' == | ||