TD-150-BLE: Difference between revisions
→Sensor calibration
| Line 174: | Line 174: | ||
* Перейти в меню "'''Настройки'''" | * Перейти в меню "'''Настройки'''" | ||
[[ | [[File:TD-150 BLE settings page.png|frameless]] | ||
* | * Insert the centralizer into the tubes | ||
* | * Fill the tubes with fuel (by sealing the drain holes with duct tape and filling the tubes, turning the sensor upside down, or submerging the sensor tubes completely in fuel) | ||
* | * Wait for the CNT level to stabilize ('''2''') | ||
* Уберите выделение с ползунка "'''Калибровка без топлива'''" ('''1''') | * Уберите выделение с ползунка "'''Калибровка без топлива'''" ('''1''') | ||
* Нажмите "'''Полный'''" ('''3''') | * Нажмите "'''Полный'''" ('''3''') | ||
* Значение "'''Полный'''"('''4''') должно измениться на значение близкое к значению текущего CNT ('''2'''), но не равно ему, так как данное значение задается согласно термокомпенсации датчика | * Значение "'''Полный'''"('''4''') должно измениться на значение близкое к значению текущего CNT ('''2'''), но не равно ему, так как данное значение задается согласно термокомпенсации датчика | ||
[[ | [[File:TD-150 BLE Full calibration.png|frameless]] | ||
[[ | [[File:Centralizer-Centrator.png|none|thumb|566x566px|'''<big>Centrator</big>''']] | ||
[[ | [[File:Centralizer.png|none|thumb|512x512px|'''<big>Centrator on the tubes</big>''']] | ||
<gallery widths="350" heights="300"> | <gallery widths="350" heights="300"> | ||
Файл:Закрытие дренажных отверстий, переворачивание датчика и заполнение трубок топливом.png|'''<big>Закрытие дренажных отверстий, переворачивание датчика и заполнение трубок топливом</big>''' | Файл:Закрытие дренажных отверстий, переворачивание датчика и заполнение трубок топливом.png|'''<big>Закрытие дренажных отверстий, переворачивание датчика и заполнение трубок топливом</big>''' | ||
| Line 191: | Line 191: | ||
</gallery> | </gallery> | ||
* | * Empty the tubes of fuel, leave the centralizer in the tubes | ||
* | * Wait for CNT to stabilize ('''2''') | ||
* | * Click "'''Empty'''" ('''3''') | ||
* | * The value "'''Empty'''" ('''4''') should change to a value close to the value of the current CNT (2), but not equal to it, since this value is set according to the temperature compensation of the sensor | ||
[[Файл:Установка пустого ТД-150 в мобильном приложении.png|975x975пкс]] | [[Файл:Установка пустого ТД-150 в мобильном приложении.png|975x975пкс]] | ||
| Line 232: | Line 232: | ||
[[Файл:Переход в настройки TD-150-BLE.png|1047x1047пкс]] | [[Файл:Переход в настройки TD-150-BLE.png|1047x1047пкс]] | ||
Select the mode you need ('''1''') and press '''“Set parameters”'''('''2''') | |||
[[Файл:Выбор режима ТД-150 мобильное приложение.png|630x630пкс]] | [[Файл:Выбор режима ТД-150 мобильное приложение.png|630x630пкс]] | ||
| Line 247: | Line 247: | ||
If you are configuring the sensor to operate in RS-485, Active RS-485, or Frequency modes, you can select the range '''1-1023 or 1-4095''' ('''1''') . In frequency mode, the range will be from '''300Hz to 1323Hz or 300Hz to 4395Hz'''. | If you are configuring the sensor to operate in RS-485, Active RS-485, or Frequency modes, you can select the range '''1-1023 or 1-4095''' ('''1''') . In frequency mode, the range will be from '''300Hz to 1323Hz or 300Hz to 4395Hz'''. | ||
After changing the range, press '''“Set parameters”''' ('''2'''). | |||
[[Файл:Выбор диапазона ТД-150 мобильное приложение.png|605x605пкс]] | [[Файл:Выбор диапазона ТД-150 мобильное приложение.png|605x605пкс]] | ||
| Line 257: | Line 257: | ||
=== '''<big>Setting the network address</big>''' === | === '''<big>Setting the network address</big>''' === | ||
The default network address of the sensor is 1; if more than one unit is installed or other LLS devices are added, the network address on the sensor may need to be changed. The network address of each sensor must also be specified in the settings of the receiving device (navigation terminal).<blockquote>'''<big>Attention!!! There cannot be two devices with the same network address on the same line; this will cause a conflict.</big>'''</blockquote> | The default network address of the sensor is 1; if more than one unit is installed or other LLS devices are added, the network address on the sensor may need to be changed. The network address of each sensor must also be specified in the settings of the receiving device (navigation terminal).<blockquote>'''<big>Attention!!! There cannot be two devices with the same network address on the same line; this will cause a conflict.</big>'''</blockquote>To change the network address, enter a new address in the range '''0-255''' in the '''“Network address”''' field ('''1''') and click “'''Set parameters'''” ('''2''') | ||
[[Файл:Изменение сетевого адреса ТД-150 мобильное приложение.png|975x975пкс]] | [[Файл:Изменение сетевого адреса ТД-150 мобильное приложение.png|975x975пкс]] | ||