TD-150: Difference between revisions
→Setting the calibration value Full and Empty manually
| Line 200: | Line 200: | ||
== '''<big>Setting the calibration value Full and Empty manually</big>''' == | == '''<big>Setting the calibration value Full and Empty manually</big>''' == | ||
We do not recommend using this functionality, but you can set the Full and Empty calibration values manually to save time when you are using sensors of the same length in the same tanks.<blockquote>'''<big>Attention!!! Setting calibration values manually will most likely increase the sensor error! We do not recommend doing this!</big>'''</blockquote>To do this, enter the Full and Empty calibration values of the previously calibrated sensor into the appropriate fields in the configurator. | |||
[[Файл:Переход в инженерное меню конфигуратора ПК.png|727x727пкс]] | [[Файл:Переход в инженерное меню конфигуратора ПК.png|727x727пкс]] | ||
| Line 322: | Line 322: | ||
| colspan="2" |'''<big>As per your capabilities. The rule of thumb is that the larger the portions and smaller the volume, the more accurate the data will be</big>''' | | colspan="2" |'''<big>As per your capabilities. The rule of thumb is that the larger the portions and smaller the volume, the more accurate the data will be</big>''' | ||
|} | |} | ||
<blockquote><big>The '''rule of thumb''': more portions means more accurate reports on the monitoring platform.</big></blockquote> | <blockquote><big>The '''rule of thumb''': more portions means more accurate reports on the monitoring platform.</big></blockquote>You can create a table on your platform by loading it from a file or by entering values manually. | ||
[[Файл:Загрузка таблицы на Wialon (пример). Не забудьте отметить "Генерировать пары XY".png|без|мини|687x687пкс|'''<big>Загрузка таблицы на Wialon (пример). Не забудьте отметить "Генерировать пары XY"</big>''']] | [[Файл:Загрузка таблицы на Wialon (пример). Не забудьте отметить "Генерировать пары XY".png|без|мини|687x687пкс|'''<big>Загрузка таблицы на Wialon (пример). Не забудьте отметить "Генерировать пары XY"</big>''']] | ||
== '''<big>Tilted tank calibration with 2 FLSs</big>''' == | == '''<big>Tilted tank calibration with 2 FLSs</big>''' == | ||
If it is not possible to level the car/tank with respect to the horizon, you can calibrate it in the tilted position of the tank. | If it is not possible to level the car/tank with respect to the horizon, you can calibrate it in the tilted position of the tank. | ||
Technically, this kind of calibration is no different from the usual one: you pour a portion of fuel into the tank, wait for the level to stabilize, fix it, and fill in the next portion. | Technically, this kind of calibration is no different from the usual one: you pour a portion of fuel into the tank, wait for the level to stabilize, fix it, and fill in the next portion. | ||
However, the details of such calibration are much more important, so the algorithm of actions should be as follows: | |||
# Pour portions of fuel into the tank until the fuel level reaches the measuring tubes of the second FLS, which is located higher due to the inclination. | # Pour portions of fuel into the tank until the fuel level reaches the measuring tubes of the second FLS, which is located higher due to the inclination. | ||
| Line 356: | Line 355: | ||
== '''<big>Filtration</big>''' == | == '''<big>Filtration</big>''' == | ||
After tank calibration is completed, select the required '''“Filtration level”''' and click '''“Save the parameters to device”''' | |||
[[Файл:Выбор степени фильтрации ТД-150 ПК.png|700x700пкс]] | [[Файл:Выбор степени фильтрации ТД-150 ПК.png|700x700пкс]] | ||
Below are recommendations for choosing the filtration level for different types of vehicles: | |||
=== | === Recommended filtration level for wired FLS === | ||
{| class="wikitable" | {| class="wikitable" | ||
|'''<big>0-1</big>''' | |'''<big>0-1</big>''' | ||
| Line 381: | Line 380: | ||
* The closer the sensor is to the tank walls, the higher the filtration is | * The closer the sensor is to the tank walls, the higher the filtration is | ||
* The worse the road surface, the higher the filtration | * The worse the road surface, the higher the filtration | ||
* | * You only need to set the median filter type | ||
[[Файл:До и после включения фильтрации на датчике.png|без|мини|814x814пкс|'''<big>Пример до установки фильтрации и после.</big>''']] | [[Файл:До и после включения фильтрации на датчике.png|без|мини|814x814пкс|'''<big>Пример до установки фильтрации и после.</big>''']] | ||
== '''<big> | == '''<big>Setting and removing a password</big>''' == | ||
If necessary, you can set a password on the sensor to change settings. | |||
To do this: | |||
* | * Click on the '''"Service"''' button ('''1''') and then '''"Security"''' ('''2''') [[Файл:Переход в меню безопасность конфигуратор ПК.png|777x777пкс]] | ||
* | * In the menu that opens, you can enter a password consisting of numbers and then click set password. '''Also note that the password cannot start with 0.''' [[Файл:Установка пароля конфигуратор ПК.png|772x772пкс]] | ||
* | * After successfully setting the password, a red lock should appear next to the FLS icon [[Файл:Датчик запаролен конфигуратор ПК.png|771x771пкс]] | ||
<blockquote>'''<big> | <blockquote>'''<big>PLEASE NOTE THAT THE PASSWORD RESET PROCEDURE CAN BE VERY TIME-CONSUMING. WE RECOMMEND THAT YOU TAKE A RESPONSIBLE APPROACH IN SETTING YOUR PASSWORD AND SAVING IT.</big>'''</blockquote>Для измения настроек запароленного датчика или удаления пароля вам нужно произвести процедуру удаления пароля | ||
* Нажмите на кнопку "'''Сервис'''"('''1''') и после "'''Безопасность'''"('''2''') [[Файл:Переход в меню безопасность конфигуратор ПК.png|777x777пкс]] | * Нажмите на кнопку "'''Сервис'''"('''1''') и после "'''Безопасность'''"('''2''') [[Файл:Переход в меню безопасность конфигуратор ПК.png|777x777пкс]] | ||