TD-150: Difference between revisions
→Setting and removing a password
| Line 393: | Line 393: | ||
* After successfully setting the password, a red lock should appear next to the FLS icon [[Файл:Датчик запаролен конфигуратор ПК.png|771x771пкс]] | * After successfully setting the password, a red lock should appear next to the FLS icon [[Файл:Датчик запаролен конфигуратор ПК.png|771x771пкс]] | ||
<blockquote>'''<big>PLEASE NOTE THAT THE PASSWORD RESET PROCEDURE CAN BE VERY TIME-CONSUMING. WE RECOMMEND THAT YOU TAKE A RESPONSIBLE APPROACH IN SETTING YOUR PASSWORD AND SAVING IT.</big>'''</blockquote> | <blockquote>'''<big>PLEASE NOTE THAT THE PASSWORD RESET PROCEDURE CAN BE VERY TIME-CONSUMING. WE RECOMMEND THAT YOU TAKE A RESPONSIBLE APPROACH IN SETTING YOUR PASSWORD AND SAVING IT.</big>'''</blockquote>To change the settings of a password-protected sensor or remove a password, you need to perform the password removal procedure | ||
* | * Click on the '''"Service"''' button ('''1''') and then '''"Security"''' ('''2''') [[Файл:Переход в меню безопасность конфигуратор ПК.png|777x777пкс]] | ||
* | * In the menu that opens, enter your password (or if you have lost your password, the master password provided by technical support) and click '''"Remove password"''' [[Файл:Удаление пароля конфигуратор ПК.png|776x776пкс]] | ||
* | * If the password was successfully removed, the lock should turn green [[Файл:Пароль на датчике удален конфигуратор ПК.png|775x775пкс]] | ||
''' | '''Attention!''' By default, there is no password set on the sensor! If you connected the sensor and a password was already set on it, contact technical support. | ||
= '''<big>Подключение к датчику, настройка, калибровка и тарировка через [https://play.google.com/store/apps/details?id=ru.fmeter.config мобильное приложение на Android]</big>''' = | = '''<big>Подключение к датчику, настройка, калибровка и тарировка через [https://play.google.com/store/apps/details?id=ru.fmeter.config мобильное приложение на Android]</big>''' = | ||
| Line 617: | Line 617: | ||
Technically, this kind of calibration is no different from the usual one: you pour a portion of fuel into the tank, wait for the level to stabilize, fix it, and fill in the next portion. | Technically, this kind of calibration is no different from the usual one: you pour a portion of fuel into the tank, wait for the level to stabilize, fix it, and fill in the next portion. | ||
However, the details of such calibration are much more important, so the algorithm of actions should be as follows: | |||
# Pour portions of fuel into the tank until the fuel level reaches the measuring tubes of the second FLS, which is located higher due to the inclination. | # Pour portions of fuel into the tank until the fuel level reaches the measuring tubes of the second FLS, which is located higher due to the inclination. | ||
# When the second sensor reaches the fuel level, reduce the size of the poured portion by half. IMPORTANT: it is necessary to reduce the portion only in the calibration tables for both FLS; the actual volume of the portion being filled remains '''unchanged'''. | # When the second sensor reaches the fuel level, reduce the size of the poured portion by half. IMPORTANT: it is necessary to reduce the portion only in the calibration tables for both FLS; the actual volume of the portion being filled remains '''unchanged'''. | ||
| Line 642: | Line 639: | ||
[[Файл:Пример_тарировочной_таблицы_ДУТ_2.png|без|мини|'''<big>Пример тарировочной таблицы ДУТ 2</big>''']] | [[Файл:Пример_тарировочной_таблицы_ДУТ_2.png|без|мини|'''<big>Пример тарировочной таблицы ДУТ 2</big>''']] | ||
== '''<big> | == '''<big>Filtration</big>''' == | ||
После того, как тарировка бака будет завершена, выберите требуемую "'''Степень фильтрации'''" ('''1''') и нажмите '''“Записать параметры в устройство”(2)''' | После того, как тарировка бака будет завершена, выберите требуемую "'''Степень фильтрации'''" ('''1''') и нажмите '''“Записать параметры в устройство”(2)''' | ||
| Line 649: | Line 646: | ||
[[Файл:Записать параметры в устройство ТД-150 мобильное приложение.png|965x965пкс]] | [[Файл:Записать параметры в устройство ТД-150 мобильное приложение.png|965x965пкс]] | ||
Below are recommendations for choosing the filtration level for different types of vehicles: | |||
=== | === Recommended filtration level for wired FLS === | ||
{| class="wikitable" | {| class="wikitable" | ||
|'''<big>0-1</big>''' | |'''<big>0-1</big>''' | ||
| Line 760: | Line 757: | ||
== '''<big>Cable sealing</big>''' == | == '''<big>Cable sealing</big>''' == | ||
To seal the sensor connector, insert a plastic seal into the special hole on the sensor connector | |||
[[Файл:Пломбирование кабеля.png]] | [[Файл:Пломбирование кабеля.png]] | ||
| Line 774: | Line 771: | ||
== '''<big>Level 7000</big>''' == | == '''<big>Level 7000</big>''' == | ||
Level 7000 is an error code Short circuit. This indicates that there is dirt, water, chips or other impurities in the tubes. All of these can be highly conductive, while the sensor is designed to work with dielectrics such as fuel. | |||
You should clean the sensor tubes - preferably by blowing them through the drain holes with compressed air. | |||
If this error occurred after the start of operation of the sensor, it means that most likely these impurities got into the sensor tubes from the tank and in this case it is also necessary to flush the tank. | |||
== '''<big>Level 6500</big>''' == | == '''<big>Level 6500</big>''' == | ||
This code may indicate that the tubes have lost contact. This error code may be generated immediately after cutting the tubes. In this case, simply calibrate the sensor. | |||
If this does not help, check the CNT. If the CNT is below 10,000, it is very likely that the tubes are not in contact with the sensor board. | |||
Take a photo of the sensor head (the sensor serial number should be visible), its tubes (the correspondence or discrepancy of the tubes length should be clearly visible), take a screenshot of the main screen of the sensor and the Settings menu page in the application and send these data to tech support. | |||
== '''<big>Датчик не подключается или не определяется в приложении</big>''' == | == '''<big>Датчик не подключается или не определяется в приложении</big>''' == | ||