TD-BLE - Revision history

Admin at 09:53, 6 February 2026

2026-02-06T09:53:05Z

← Older revision		Revision as of 12:53, 6 February 2026
Line 273:		Line 273:
	You can use collet extension and an additional tube. to extend tubes length.		You can use collet extension and an additional tube. to extend tubes length.

	It is not reccomended to use more 1 extension.		It is not reccomended to use more than '''one''' collect extension.
	[[File:Collet connection.png\|none\|thumb\|875x875px\|'''Collet connection''']]		[[File:Collet connection.png\|none\|thumb\|875x875px\|'''Collet connection''']]

Admin at 09:42, 6 February 2026

2026-02-06T09:42:55Z

← Older revision		Revision as of 12:42, 6 February 2026
Line 271:		Line 271:
	'''Avoid getting shavings inside the tubes - this may lead to a short circuit in the sensor; if this happens, blow the tubes with compressed air through the drainage holes under the sensor flange.''' Sand the edges of the tubes with sandpaper to remove any burrs or irregularities.		'''Avoid getting shavings inside the tubes - this may lead to a short circuit in the sensor; if this happens, blow the tubes with compressed air through the drainage holes under the sensor flange.''' Sand the edges of the tubes with sandpaper to remove any burrs or irregularities.

	~~To extend sensor tubing,~~ use a collet extension and an additional tube.		You can use collet extension and an additional tube. to extend tubes length.

			It is not reccomended to use more 1 extension.
	[[File:Collet connection.png\|none\|thumb\|875x875px\|'''Collet connection''']]		[[File:Collet connection.png\|none\|thumb\|875x875px\|'''Collet connection''']]

VLADISLAV: /* How many portions should I add? */

2025-11-27T15:32:07Z

How many portions should I add?

← Older revision		Revision as of 18:32, 27 November 2025
Line 390:		Line 390:
	[[File:Tank calibration table in .csv format.png\|none\|thumb\|'''Tank calibration table in .csv format''']]		[[File:Tank calibration table in .csv format.png\|none\|thumb\|'''Tank calibration table in .csv format''']]

	== '''<big>How many portions should I add?</big>''' ==		== '''<big>How many portions should I add</big>''' ==
	The total number of portions depends on the capacity of the tank. Below is a table with guidelines.		The total number of portions depends on the capacity of the tank. Below is a table with guidelines.
	{\| class="wikitable"		{\| class="wikitable"

VLADISLAV: /* Examples of sealants recommended by the community: */

2025-11-18T16:00:10Z

Examples of sealants recommended by the community:

← Older revision		Revision as of 19:00, 18 November 2025
Line 763:		Line 763:
	Instead of a 2-component compound, you can use oil-gasoline-resistant sealants that are neutral in acidity (on an acetic-free base)		Instead of a 2-component compound, you can use oil-gasoline-resistant sealants that are neutral in acidity (on an acetic-free base)

	=== Examples of sealants recommended by the community: ===		=== Examples of sealants recommended by the community ===
	[[File:ABRO 999.png\|none\|thumb\|'''<big>ABRO 999 RED</big>''']]		[[File:ABRO 999.png\|none\|thumb\|'''<big>ABRO 999 RED</big>''']]
	[[File:ABRO 999 GREY.png\|none\|thumb\|'''<big>ABRO 999 GREY</big>''']]		[[File:ABRO 999 GREY.png\|none\|thumb\|'''<big>ABRO 999 GREY</big>''']]

VLADISLAV: /* Level 7000 */

2025-10-12T13:48:26Z

Level 7000

← Older revision		Revision as of 16:48, 12 October 2025
Line 635:		Line 635:
	You should clean the sensor tubes preferably by flushing them with the clean fuel and blowing them through the drain holes with compressed air.		You should clean the sensor tubes preferably by flushing them with the clean fuel and blowing them through the drain holes with compressed air.

	If this error occurred after the start of operation of the sensor, it means that most likely these impurities got into the sensor tubes from the tank and in this case it is also needed to ensure that the tank itself doesn't contain any ~~impurities~~. Clean the tank, if necessary. Note that a fuel level sensor installed outside a contaminated tank may function correctly, but the same sensor installed in such a tank may generate this error code.		If this error occurred after the start of operation of the sensor, it means that most likely these impurities got into the sensor tubes from the tank and in this case it is also needed to ensure that the tank itself doesn't contain any contaminations. Clean the tank, if necessary. Note that a fuel level sensor installed outside a contaminated tank may function correctly, but the same sensor installed in such a tank may generate this error code.

	== '''<big>Level 6500</big>''' ==		== '''<big>Level 6500</big>''' ==

VLADISLAV: /* Level 7000 */

2025-10-12T13:41:09Z

Level 7000

← Older revision		Revision as of 16:41, 12 October 2025
Line 633:		Line 633:
	[[File:Level 7000.png\|frameless]]		[[File:Level 7000.png\|frameless]]

	You should clean the sensor tubes - preferably by blowing them through the drain holes with compressed air.		You should clean the sensor tubes preferably by flushing them with the clean fuel and blowing them through the drain holes with compressed air.

	If this error occurred after the start of operation of the sensor, it means that most likely these impurities got into the sensor tubes from the tank and in this case it is also necessary ~~to flush~~ the tank.		If this error occurred after the start of operation of the sensor, it means that most likely these impurities got into the sensor tubes from the tank and in this case it is also needed to ensure that the tank itself doesn't contain any impurities. Clean the tank, if necessary. Note that a fuel level sensor installed outside a contaminated tank may function correctly, but the same sensor installed in such a tank may generate this error code.

	== '''<big>Level 6500</big>''' ==		== '''<big>Level 6500</big>''' ==

ROMAN at 10:03, 20 June 2025

2025-06-20T10:03:04Z

← Older revision		Revision as of 13:03, 20 June 2025
Line 299:		Line 299:
	File:Installing the sensor inside the tank.png\|'''<big>Installing the sensor inside the tank</big>'''		File:Installing the sensor inside the tank.png\|'''<big>Installing the sensor inside the tank</big>'''
	File:Screwing the self-tapping screws.png\|'''<big>Screwing the self-tapping screws</big>'''		File:Screwing the self-tapping screws.png\|'''<big>Screwing the self-tapping screws</big>'''
	</gallery>Proceed to tank calibration. This procedure will result in a "level-liters" (or "level-gallons") table that will allow your monitoring platform to convert the level values that the sensor provides into liters/gallons that are displayed in the monitoring platform reports. You can save the table to the sensor's memory so that the sensor immediately outputs volume values in liters/gallons. You do not need to enter a calibration table on the monitoring platform. The internal memory of the TD BLE sensor can hold up to 50 lines of the calibration table. The capacity of the table on the monitoring platform is usually larger.<blockquote>In addition, it is easier to change the table or correct errors in the calibration table when it is downloaded to the platform than if the table is stored in the sensor's memory</blockquote>In order to create such a table, you need to fill the tank by step by step adding fuel to the tank batch by batch and recording level-liter(/gallon) value pairs after each batch using the ~~Tare~~ menu in the application.		</gallery>Proceed to tank calibration. This procedure will result in a "level-liters" (or "level-gallons") table that will allow your monitoring platform to convert the level values that the sensor provides into liters/gallons that are displayed in the monitoring platform reports. You can save the table to the sensor's memory so that the sensor immediately outputs volume values in liters/gallons. You do not need to enter a calibration table on the monitoring platform. The internal memory of the TD BLE sensor can hold up to 50 lines of the calibration table. The capacity of the table on the monitoring platform is usually larger.<blockquote>In addition, it is easier to change the table or correct errors in the calibration table when it is downloaded to the platform than if the table is stored in the sensor's memory</blockquote>In order to create such a table, you need to fill the tank by step by step adding fuel to the tank batch by batch and recording level-liter(/gallon) value pairs after each batch using the tank calibration menu in the application.

	Suppose you need to ~~tare~~ a 100 L tank in ten 10 L portions.		Suppose you need to calibrate a 100 L tank in ten 10 L portions.

	To do this, you should connect the sensor, press the '''"Tank calibration"''' '''(2)''' button . But before that, in the '''"Settings" (3)''' menu , make sure that the filtering level is selected '''0 (4)'''. Filtration slows down the level calculation and can increase the tank calibration time.<gallery mode="nolines" widths="300" heights="600">		To do this, you should connect the sensor, press the '''"Tank calibration"''' '''(2)''' button . But before that, in the '''"Settings" (3)''' menu , make sure that the filtering level is selected '''0 (4)'''. Filtration slows down the level calculation and can increase the tank calibration time.<gallery mode="nolines" widths="300" heights="600">

ERNEST: /* Connection dimensions of the TD-BLE of the former design */

2025-04-10T10:02:18Z

Connection dimensions of the TD-BLE of the former design

← Older revision		Revision as of 13:02, 10 April 2025
Line 311:		Line 311:
	</gallery>If you click Start, you will also need to select the folder in which the table will be saved '''(2)''' and click the button to select it '''(3)'''		</gallery>If you click Start, you will also need to select the folder in which the table will be saved '''(2)''' and click the button to select it '''(3)'''
	[[File:Start tank calibration folder.png\|none\|thumb\|Selecting a folder and creating new calibration files]]		[[File:Start tank calibration folder.png\|none\|thumb\|Selecting a folder and creating new calibration files]]

			Select the calibration type Manual '''(2).'''

			Mathematical calibration '''(1)''' is [[TD-BLE#Mathematical calibration\|shown in this article.]]

			[[File:Selecting type of tank calibration .png]]

	Then, you can select the '''Fill''' or '''Drain''' method '''(1, 2)'''. The '''Fill''' method is recommended as it is more accurate.		Then, you can select the '''Fill''' or '''Drain''' method '''(1, 2)'''. The '''Fill''' method is recommended as it is more accurate.
Line 456:		Line 462:

	== '''<big>Mathematical calibration</big>''' ==		== '''<big>Mathematical calibration</big>''' ==
	The mobile application has the ability to create a mathematical calibration table based on the tank size, this functionality is recommended to be used only on large tanks where it is not possible to perform ~~classic~~ calibration by filling/draining.		The mobile application has the ability to create a mathematical calibration table based on the tank size, this functionality is recommended to be used only on large tanks where it is not possible to perform manual calibration by filling/draining.

	To create a mathematical calibration, go to the sensor calibration menu '''(2)'''		To create a mathematical calibration, go to the sensor calibration menu '''(2)'''

ERNEST: /* Tank calibration */

2025-04-10T09:58:57Z

Tank calibration

@@ Line 454: / Line 454: @@
 [[File:Tilted FLS 1.png|none|thumb|'''<big>Tank calibration example FLS 1</big>''']]
 [[File:Height FLS 2.png|none|thumb|'''<big>Tank calibration example FLS 2</big>''']]
 = '''<big>Filtration</big>''' =

ERNEST: /* Additional settings */

2025-04-10T09:49:31Z

Additional settings

← Older revision		Revision as of 12:49, 10 April 2025
Line 554:		Line 554:
	In the Additional settings menu, there is an option to disable temperature compensation '''(1).'''<blockquote>'''ATTENTION!''' It is not recommended to change the position of the temperature compensation switch '''(it should remain green)''' if you do not use your own temperature compensation algorithm.</blockquote>Data encryption '''(2)''' option works only when connecting with RS-485 BLE base or BA-BLE.		In the Additional settings menu, there is an option to disable temperature compensation '''(1).'''<blockquote>'''ATTENTION!''' It is not recommended to change the position of the temperature compensation switch '''(it should remain green)''' if you do not use your own temperature compensation algorithm.</blockquote>Data encryption '''(2)''' option works only when connecting with RS-485 BLE base or BA-BLE.

	[[File:Additional settings tab.png\|frameless]]		[[File:Additional settings tab.png\|frameless\|800x800px]]

	== <big>'''Manually setting Full and Empty calibration values'''</big> ==		== <big>'''Manually setting Full and Empty calibration values'''</big> ==